Home » Page 4
Page 4 List
What is the four-way valve
The four-way valve or four-way cock is a fluid control valve whose body has four ports equally spaced round the valve chamber and the plug has two passages to connect adjacent ports. The plug may be cylindrical or tapered, or a ball.It has two flow positions as shown, and usually a central position where all ports are closed.It can be...What is the sampling valve
A Sampling Valve is a type of valve used in process industries that allows taking a representative portion of a fluid (gases, liquids, fluidized, solids, or slurries) to test (e.g. by physical measurements, chemical analysis, microbiological examination), typically for the purposes of identification, quality control, or regulatory asse...What is the pinch valve
A pinch valve is a full bore or fully ported type of control valve which uses a pinching effect to obstruct fluid flow.Operating principlePinch valves employ an elastic tubing (sleeve/hose) and a device that directly contacts the tubing (body). Forcing the tubing together will create a seal that is equivalent to the tubing's perme...What is the plug valve
Plug valves are valves with cylindrical or conically tapered "plugs" which can be rotated inside the valve body to control flow through the valve. The plugs in plug valves have one or more hollow passageways going sideways through the plug, so that fluid can flow through the plug when the valve is open. Plug valves are simple...What is the saddle valve
A saddle valve is a valve used to supply liquid where a low volume, low pressure stream is required. The name is derived from the fact that it is mounted in such a way that it "saddles" the line, mounting it from both sides.They are typically used for supplying cold water, via a 3/8 inch tube, to:humidifiers andicemakers in f...What is the double check valve
A double check valve or double check assembly (DCA) is a backflow prevention device designed to protect water supplies from contamination. It is also a valve used in air brake systems on heavy trucks.It consists of two check valves assembled in series.[1] This employs two operating principles: firstly one check valve will still act...What is the flow control valve
A flow control valve regulates the flow or pressure of a fluid. Control valves normally respond to signals generated by independent devices such as flow meters or temperature gauges.OperationControl valves are normally fitted with actuators and positioners. Pneumatically-actuated globe valves and diaphragm valves are widely used for ...What is the hut down valve
A shut down valve (also referred to as SDV or Emergency Shutdown Valve, ESV, ESD, or ESDV) is an actuated valve designed to stop the flow of a hazardous fluid upon the detection of a dangerous event. This provides protection against possible harm to people, equipment or the environment. Shutdown valves form part of a S...What is the Check valve
A check valve, clack valve, non-return valve, reflux valve, retention valve or one-way valve is a valve that normally allows fluid (liquid or gas) to flow through it in only one direction.Check valves are two-port valves, meaning they have two openings in the body, one for fluid to enter and the other for fluid to leave. There are vari...What is the Reversing valve
A reversing valve a type of valve and is a component in a heat pump, that changes the direction of refrigerant flow. By reversing the flow of refrigerant, the heat pump refrigeration cycle is changed from cooling to heating or vice versa. This allows a residence or facility to be heated and cooled by a single piece of equipment, by the...What is the Automatic balancing valve
Automatic balancing systemsPurposeA cooling or heating water distribution system is in the balance when the flow in the whole system (through the component terminal lines, distributing lines and main distributing lines) corresponds to the flow rates that were specified for the design of the system. If the correct balancing of the syst...What is the Desmodromic valve
In general mechanical terms, the word desmodromic is used to refer to mechanisms that have different controls for their actuation in different directions.A desmodromic valve is a reciprocating engine poppet valve that is positively closed by a cam and leverage system, rather than by a more conventional spring.The valves in a typical fo...What is the Schrader valve
The Schrader valve (also called American valve is a type of pneumatic tire valve used on virtually every motor vehicle in the world today. The Schrader company, for which it was named, was founded in 1844 by August Schrader. The original Schrader valve design was invented in 1891, and patented in the United States in 1893.The ...What is the Relief valve
A relief valve or pressure relief valve (PRV) is a type of safety valve used to control or limit the pressure in a system; pressure might otherwise build up and create a process upset, instrument or equipment failure, or fire. The pressure is relieved by allowing the pressurised fluid to flow from an auxiliary passage out of the syst...What is the valve actuator
A valve actuator is the mechanism for opening and closing a valve. Manually operated valves require someone in attendance to adjust them using a direct or geared mechanism attached to the valve stem. Power-operated actuators, using gas pressure, hydraulic pressure or electricity, allow a valve to be adjusted remotely, or allow rapid op...What is the Adjustable pressure-limiting valve
An adjustable pressure-limiting valve (commonly abbreviated to APL valve, and also referred to as an expiratory valve, relief valve or spill valve) is a type of flow control valve used in anaesthesiology as part of a breathing system. It allows excess fresh gas flow and exhaled gases to leave the system while preventing ambient air f...What is the Thermal expansion valve
A thermal expansion valve (often abbreviated as TEV, TXV, or TX valve) is a component in refrigeration and air conditioning systems that controls the amount of refrigerant released into the evaporator thereby controlling superheat. Thermal expansion valves are often referred to generically as "metering devices".Descri...OCTOBER 3 & 4, 2019, BOMBAY CONVENTION & EXHIBITION CENTRE GOREGAON (EAST), MUMBAI, INDIA
Flow Control Exchange India is a unique combination of technical conference, exhibition and workshops focusing on valves, actuation and all related technologies in flow control systems. Local and international suppliers and end users will embrace this opportunity to expand their business networks and technical knowledge.Flow Contro...Pumps & Valves Asia 2019
PUMPS & VALVES ASIA 2019 is Thailand's 18th largest and most international exhibition of Pumps, Valves and Fittings. It is the only specialized international exhibition in Thailand. The leading trade show focuses on the technologies and innovations in industrial pumps, valves, seals and other major processing...Pumps & Valves Rotterdam 2019
On the 2nd and 3rd of October 2019, experts in fluids processing, handling, and transport will gather in Rotterdam Ahoy to do business. Pumps & Valves and the trade event Solids are co-located. With over 250 exhibitors, Solids and Pumps & Valves form the biggest platform for the dry and liq...